users should evaluate the suitability of this product for their application. specifcations are subject to change without notice. tyco electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specifcation, without notifcation to buyer. 1 / colors and color code designators shall be in accordance with mil-std-681. however, due to length limitations of the raychem part number, an alternative color code may replace mil-std-681 color code designators. (example: 901/902... may be replaced by axxx.) other codes and suffixes may be added to the part number, as necessary, to capture any additional requirements imposed by the purchase order. page 1 of 2 the te logo, tyco electronics and raychem are trademarks. raychem wire & cable 501 oakside avenue redwood city, ca 94063-3800 phone: 1-800-227-8816 fax: 1-650-361-6297 dimensions are in inches, and unless otherwise designated are nominal this specification sheet takes precedence over documents referenced herein. referenced documents shall be of the issue in effect on date of invitation for bid. ? 2007-2010 tyco electronics corporation. all rights reserved. component wires - 55pc0113 shield - nickel-coated copper jacket - radiation-crosslinked, modified etfe specification control drawing 55PC1133 three conductor cable, shielded, jacketed, general purpose, 600 volt 7-28-10 c this specifcation sheet forms a part of the latest issue of raychem specifcation 55pc. title date revision construction details part number 1/ conductor size (awg) shield size (awg) jacket thickness ( in. ) outside diameter ( in. ) weight ( lbs/1000 ft. ) lower spec limit target wall lower spec limit target value upper spec limit target value upper spec limit 55PC1133-26-* 26 38 .0055 .0070 .094 .098 .102 8.87 9.32 55PC1133-24-* 24 38 .0055 .0070 .104 .108 .113 11.23 11.67 55PC1133-22-* 22 38 .0060 .0075 .118 .122 .127 14.85 15.39 55PC1133-20-* 20 38 .0060 .0075 .135 .139 .144 20.30 20.91 55PC1133-18-* 18 38 .0060 .0075 .155 .160 .165 28.14 28.94 55PC1133-16-* 16 38 .0060 .0080 .172 .177 .182 34.67 35.57 55PC1133-14-* 14 38 .0060 .0080 .203 .208 .214 50.00 51.12 55PC1133-12-* 12 38 .0060 .0080 .244 .249 .255 73.31 74.78 55PC1133-10-* 10 36 .0065 .0085 .295 .310 .325 116.67 120.59 55PC1133-8-* 8 34 .0070 .0090 .426 .449 .472 218.12 225.11
cable ratings and additional requirements revision specification control drawing page 2 of 2 c 55PC1133 scd temperature rating: 200c maximum continuous conductor temperature voltage rating: 600 volts (rms) at sea level crosslink verification: 300 3c for 1 hour dielectric withstand: 1500 volts (rms), 60 hz jacket color: white preferred jacket elongation and tensile strength: elongation, 50% (minimum) tensile strength, 5000 lbf/in2 (minimum) jacket flaws: spark test, 1000 volts (rms) impulse dielectric test, 6.0 kv (peak) shield coverage: 85% (minimum) voltage withstand test (post environmental): 1000 volts (rms), 60 hz, 1 minute part number: the "*" in the part numbers on page 1 shall be replaced by color code designators with a slash separating the component wire colors and a dash separating the component wire colors from the jacket color. colors shown do not necessarily refect the sequence of manufacturing. 1 / example: awg 22, red, yellow and blue component wires; white jacket: 55PC1133-22-2/4/6-9 1/ see footer section on page 1
|
